#Ehome infrared receiver colossus 2 driver#
#Ehome infrared receiver colossus 2 tv#

ata6: SATA max UDMA/133 abar port 0xf8effb80 irq 46

ata5: SATA max UDMA/133 abar port 0xf8effb00 irq 46 ata2: SATA max UDMA/133 abar port 0xf8eff980 irq 46 ata1: SATA max UDMA/133 abar port 0xf8eff900 irq 46 rtc0: alarms up to one month, ењ“k, 114 bytes nvram, hpet irqs Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled ACPI: PCI Interrupt Link (IRQs 3 4 6 7 10 11 12 14 15) *0, disabled. Booting paravirtualized kernel on bare hardware ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) kernel direct mapping tables up to 140000000 bff8a000-bff90000 kernel direct mapping tables up to bff90000 1fffb000-20000000

Repeat delay = 500 ms, repeat period = 125 ms Supported protocols: NEC RC-5 RC-6 JVC SONY LIRC other sys/class/rc/rc0/protocols protocol lirc (disabled)ДЇound /sys/class/rc/rc0/ (/dev/input/event8) with: sys/class/rc/rc0/protocols protocol mce_kbd (disabled) sys/class/rc/rc0/protocols protocol sanyo (disabled) sys/class/rc/rc0/protocols protocol sony (disabled) sys/class/rc/rc0/protocols protocol jvc (disabled) sys/class/rc/rc0/protocols protocol rc-6 (enabled) sys/class/rc/rc0/protocols protocol nec (disabled) sys/class/rc/rc0/protocols protocol rc-5 (disabled) sys/class/rc/rc0/uevent uevent DRV_NAME=ene_ir

sys/class/rc/rc0/uevent uevent NAME=rc-rc6-mce sys/class/rc/rc0/input8/event8/uevent uevent DEVNAME=input/event8 sys/class/rc/rc0/input8/event8/uevent uevent MINOR=72 sys/class/rc/rc0/input8/event8/uevent uevent MAJOR=13 Parsing uevent /sys/class/rc/rc0/input8/event8/uevent It works fine under Linux, so the receiver is OK.Input sysfs node is /sys/class/rc/rc0/input8/Д®vent sysfs node is /sys/class/rc/rc0/input8/event8/ Tried mode2 -d /dev/lirc0, tried od -x /dev/input/event0 to rule out any lirc config issues, but nothing. INFO: : 2 tx ports (0x0 cabled) and 2 rx sensors (0x0 active)ДBG: rc0: lirc_dev (ir-lirc-codec (mceusb)): open calledДBG: rc0: lirc_dev (ir-lirc-codec (mceusb)): open result = 0ДBG: rc0: lirc_dev (ir-lirc-codec (mceusb)): close calledД«ut it doesn't work. INFO: : Registered Philips eHome Infrared Transceiver with mce emulator interface version 1

#Ehome infrared receiver colossus 2 driver#

INFO: rc0: lirc_dev: driver ir-lirc-codec (mceusb) registered at minor = 0 eHome Infrared Remote Transceiver (0471:0815) as webcamdДBG: rc0: lirc_dev: lirc_register_driver: sample_rate: 0

#Ehome infrared receiver colossus 2 tv#

Uvcvideo: Unable to create debugfs directoryД«2c2-flexcop: B2C2 FlexcopII/II(b)/III digital TV receiver chip loaded successfully Pvrusb2: V4L in-tree version:Hauppauge WinTV-PVR-USB2 MPEG2 Encoder/TunerД¬pia2: V4L-Driver for Vision CPiA2 based cameras v3.0.1 USBVision USB Video Device Driver for Linux : 0.9.11 IR RC5 (streamzap) protocol handler initializedД®m28xx: Initialized (Em28xx dvb Extension) extension Lirc_dev: IR Remote Control driver registered, major 14 ~]# webcamd -U webcamd -G webcamd -i 0 -H